What the Clover Knicker's cut actually gives you
The Clover Knicker is a mid-rise, mid-leg knicker with a quatrefoil motif lace front and a completely backless rear. The back is held by four adjustable straps rather than fabric, and the piece is finished with a moss green silky bow. That construction is the whole fit story: the front and sides behave like a standard mid-rise knicker, while the back has no panel to sit against you.
Because the back is open, the usual knicker checks — does the back ride up, does the leg line dig in — apply mainly to the front and side edges. The four straps do the rear work, and they are adjustable, so you set how the back sits rather than accepting a fixed cut.
Clover Knicker details that affect fit
- Clover Knicker: Mid rise, mid leg, backless with four adjustable back straps. Tells you where the waistband sits and that the rear fit is set by straps, not a fabric panel.

Clover Knicker - Clover Knicker: Cotton jersey gusset. The gusset is the part that sits closest to the body, so it is worth checking it lies flat when you first try the knicker on.
- Clover Knicker: Soft elastic edges and French seams. These are the construction details most likely to affect comfort at the leg and waist edges.
- Clover Knicker: Embroidered tulle lace with a quatrefoil motif. Lace has less stretch than jersey, so the front fit depends on choosing the right size rather than relying on give.
How to choose your Clover Knicker size
The Clover Knicker comes in sizes 6–22. The product page points you to the sizing page for measurements, and custom sizing is handled through the Atelier section. Work through these checks in order.
- Measure, then match to the sizing page: Take your hip and waist measurements and compare them with the sizing page rather than guessing from your usual size. The lace front has limited stretch, so the measurement match matters more than it would on a jersey knicker.
- Check the waistband sits where you expect: This is a mid-rise knicker. Put it on and confirm the waistband sits at the height you want before adjusting anything else.
- Set the four back straps: Adjust the straps so the back sits where you want it. Because they are adjustable, you can fine-tune the rear fit independently of the front.
- Check the gusset and leg edges: Confirm the cotton jersey gusset lies flat and the soft elastic edges are not rolling or digging in. If they are, revisit the size before deciding.
- Use the Atelier route if standard sizes do not match: If your measurements fall outside what sizes 6–22 cover, the product page directs you to the Atelier section for custom sizing.
What backless coverage means in practice
Clover Knicker coverage is best described as full at the front and sides, open at the back. The mid-leg cut gives more coverage at the leg than a high-leg brief, while the four straps leave the rear exposed. That makes it a piece to choose deliberately: it works when you want the back detail to be part of the look, and it is not the knicker to reach for when you want a full fabric seat.
The tradeoff is straightforward. You get the quatrefoil lace front and the strap detail across the back, but you give up the rear panel that would normally keep a knicker in place. The adjustable straps are what compensate, so take the time to set them rather than leaving them at their default length.
Styling the Clover Knicker
The backless construction and the moss green bow set the styling direction. These are starting points, not rules.
- Let the back straps be seen: The four straps are the feature. Under a sheer or open-back layer, or worn as the visible bottom of a set, they do the work the fabric panel usually would.
- Keep the front line clean: The quatrefoil lace is busy enough on its own. A plain or tonal top lets the lace read clearly rather than competing with it.
- Pick up the moss green bow: The bow is a small detail with a distinct colour. Echoing moss green elsewhere, or keeping everything else neutral, stops it looking accidental.
- Treat it as a deliberate piece, not a daily basic: With a backless rear and limited stock, the Clover Knicker is better suited to occasions where you want the detail to show than to everyday rotation.
Comfort checks worth doing on the first wear
The supplied details point to three comfort factors: the soft elastic edges, the French seams, and the adjustable back straps. On the first wear, check that the elastic edges at the waist and legs are sitting flat rather than folded, and that the seams are not pressing into the skin. Then re-check the strap adjustment after you have moved around — straps set while standing still can feel different once you sit down.
If something is uncomfortable, adjust the straps first, since they are the one part designed to be changed. If the front or leg edges are the problem, the size is the more likely cause.
Care that keeps the lace and straps in shape
Nether items should be hand washed with gentle detergents and never tumble dried. That applies to the Clover Knicker as much as anything else in the range. Hand washing protects the embroidered tulle lace and the shape of the soft elastic edges; tumble drying is the step to avoid entirely.
Because the knicker is cut and stitched once you order, with 10–14 days allowed, it is worth getting the care routine right from the first wash rather than replacing a piece that took time to arrive.
Ordering the Clover Knicker
- Clover Knicker: Cut and stitched once you order, with 10–14 days allowed. Sets the timeline between ordering and wearing, so plan around it rather than expecting next-day dispatch.
- Clover Knicker: Just 3 sets available. Limited stock means the size you need may not be there later, so confirm your size before ordering.
- Clover Knicker: Available in sizes 6–22. The full size range to check against your measurements on the sizing page.
- Clover Knicker: Hand wash with gentle detergents and never tumble dry. The care instruction to follow from the first wash to keep the lace and elastic in shape.

